Haven't seen these in a while and have forgotten how we handled them. I think it's a model 20. What kind of fixture can be used to replace this??
Thanks
You need to be a member of Pool Genius Network™ to add comments!
This reply was deleted.
If you are a member of the "pool industry" community, you have found your home.
This is a network of pool builders, service professionals, retailers, and pool sales reps,…
For…
Swimming pools are often associated with luxury, relaxation, and endless summer fun. But there's more than just the allure of crystal-clear water that leads a…
The Journal of the Swimming Pool and Spa Industry is coming back! JSPSI, a peer-reviewed technical journal, began in 1995 as a subscription-supported print-based publication. It contained articles at a technical…
All pool plaster finishes should last 20 years or more. However, some last only 5 to 7 years, and some less than a year before the plaster surface deteriorates, discolors, and looks terrible.
Why the difference? Very often, plaster…
For 50 years, the pool industry has considered pool water within an LSI of -0.3 and +0.5 to be acceptable and balanced. But recently, and without providing any supporting science or research, the NPC is trying to convince the industry that any…
There are two important issues involved when trying to achieve quality colored pool plaster that will remain durable, attractive, and the proper shade for many years.
The first issue is to utilize superior workmanship practices to achieve…
Replies
Hank,
I just pulled an Anthony model 21 pool light. I'm looking for a replacement pool light that will fit my existing pool niche. I have included some photos for your comments. The pool supply houses I've dealt with recommend installing new Pentair plaster repair ring. I have more photos if needed
Bill
IMG_0951.JPG
IMG_0952.JPG
My best guess is going to be the Sta-Rite part# 05082-0025 (for 25' cord) 0050 (for 50' cord) -0100 (for 100' cord) I'm in a 12v market but this is the same light except for 120V.
Part of the problem is that because of U.L listing and other regulations, manufacturer's cannot recommend any light not tested by UL for the receiving niche. Also, for liability reasons in the event of some kind of problem resulting in damage, injury or death. So I am adding a disclaimer that while this light will physically fir in the niche, it is not sold for that purpose.
Thank you so much for your comments Hank. I plan on having a certified electrician do the installation and conduct grounding and bonding tests. I completely understand the liability issues stated by manufacturer and your disclaimer.
Bill
Hank is right about UL listing, etc..
Keep in mind also regarding the bonding, the screw that secures the light to the niche completes the bonding of the light itself for both stainless and PVC niches. The plaster ring you showed must be bonded along with the existing niche. It gets a little tricky.
GFCI PROTECT THE LIGHT FIXTURE!!!
Hank
I remember these lights from years ago. I'm not certain, but I believe Anthony used Swimquip lights.
Pentair may have a replacement.
Some light companies have adapter plates to convert to smaller LED light.
Securing a replacement light properly to the existing niche is paramount. The set screw must secure the fixture properly so it cannot be pulled out by a bather, and also for proper bonding. This last aspect is SUPER important!
It's a good idea to have a certified individual to perform a bond test. It protects you and your customer. Also, by code, the light must be GFCI protected.
Anthony generally used a GFCI receptacle to protect the pool lights. The receptacles always seemed to be very low to the ground.
Problem is the GFCI's fail at some point due to the elements. Bubble cover requirements are fairly new to protect receptacles.
Yeah,I get all that. Been doing pools for over 40 years! Pentair is very careful not to make recommendations. The (Aladdin) adapter rings don't fit the Anthony niche, at least not well. I believe I have found the old Swimquip part number for the smaller light (8 1/2") 05082-0050 (50' cord, 12V) that can still be ordered.
Thanks for your reply and assistance!