Forum

Replies

• 

  Randy Mann October 23, 2010 at 6:33pm

  magic jacks lube,
• 

  Jeremy Hine October 23, 2010 at 6:27pm

  Randy,
  
  im not familiar with using a little jacks. Can you explain?
  
  -Jeremy
  Florida Leisure Pool & Spa
  www.FLLeisure.com
  
  Randy Mann said:

  i just use a little jacks, if it rolls out again i sell them a new multi port then show them how to push the handle down all the way

  Florida Leisure Pool, Spa, Hot Tub Repair, Pumps, Filters, Heaters, Salt Chlorinators, Automation

  We repair pools, spas and hot tubs, pumps, motors, heaters, filters, automation equipment in Gainesville and North Central FL
• 

  Randy Mann October 23, 2010 at 6:10pm

  i just use a little jacks, if it rolls out again i sell them a new multi port then show them how to push the handle down all the way
• 

  Breakpoint Commercial Pool Systems, Inc. September 14, 2009 at 9:48pm

  Anybody use hot glue, ya know, the kind crafters use to glue stuff together? A small electric "gun" heats up a glue stick the size of a pencil. Nothing to dry out, flexible, cheap, sticky as can be, water resistant. Hmmm, that just might work!
• 

  Bruce Hudson September 12, 2009 at 5:21am

  Really appreciate all the feedback. I still like the 3M DP-105 but sure feel better about discovering that the cartridge is empty.
  
  Many years ago an older tech also advised that one pour water under the handle while operating it to flush the dirt out and allow it to turn easier. It does seem to help. I also agree with turning the handle only one direction, and like Todd says, handles and washers are very important for proper operation and they DO wear out.
• 

  John Dauzat September 11, 2009 at 9:03pm

  I have heard of (or done) all of the following: my initial instructions from my first boss when I got in the biz was...super glue gel. The next place I worked for advised me that nothing should be used, due to the fact of the complexity of removing it. Lastly, when I did pool service, I had a very experienced pool guy tell me to use the yellow (or orange) window sealant stuff that you can get at an auto parts store. One thing that I have seen in several of the comments is that you always, without a doubt, turn the handle in the same direction. I definitely agree with that.
• 

  brian thomas August 21, 2009 at 7:02pm

  I dont use any adhesive i just fit it in and lube up the gasket with ''magic lube'' silicone lube, also you should try turning the valve only in one direction it might stop the binding or rolling of the gasket. One service i offer is to rebuild the multi-port, including replacing the shaft o-rings and spring which ussally helps with older multi-ports.
  There is a tool out there called "the bubba" (multi-port press tool) which works well for getinng the diverter apart to replace the o-rings and spring check it out. I got mine in 2 weeks to key west from california. Heres the website and good luck I hope it helps some.
  http://www.toolsforpools.com/Lass_pgs/bubba.htm
• 

  Greg Boutte August 21, 2009 at 6:40pm

  good old super glue for me
• 

  Todd Rafkin August 19, 2009 at 8:12am

  I used 3m weather strip adhesive for some time it worked good the valve body has to be very dry, then one day i replaced a spider gasket, spring, handle and teflon washer (i'm old school) i did not have any adhesive not even pvc glue, i know people who use that so, i did not use anything and i figured the diverter would hold most of the gasket down correct me if i am wrong i think all sides of the opening on the diverter will hold down the gasket. Make sure the diverter does not drag over the top of the gasket when changing positions good handles and washers a must, any way it worked what i am trying to say is i don't use adhesives any more. That may not be the way to go but has worked for me so far, i do try to do things the right way. Sorry for the lecture....
  Todd
• 

  Scott Heusser August 3, 2009 at 2:21pm

  I haven't used any adhesive for years. I instruct the client to stop at each detente and allow the gasket to be re-seated, then to the next, and to the next....etc. I also instruct them to turn the valve ONE direction, normally clockwise. I don't replace many gaskets after the client adopts this method.